Una spesa di almeno 50€.
Peso della bobina: 750 g.
MetalFil – Brass è un filamento a base di PLA con l’aggiunta di metallo. Questo incredibile elevato riempimento con polveri di ottone consente a tutti gli utenti di stampanti 3D FDM di stampare in 3D oggetti in ottone che sono quasi indistinguibili dagli oggetti in fusione di ottone genuini. Gli oggetti stampati MetalFil Brass sono estremamente facili da lucidare.
€31,15 + IVA
General printing guidelines *
|Nozzle size: ≥ 0.4mm||Layer height: ≥ 0.1mm||Flow rate: ± 110%|
|Print temp: ± 180 – 195° C *||Print speed: Medium||Retraction: Yes ± 5mm|
|Heat bed: ± 0 – 60° C + Blue Tape||Fan speed: 50-100%||Experience level: Beginner|
*) Above displayed settings are meant as guidance to find your optimal print settings. These ranges in settings should work for most printers, but please do feel free to experiment outside these ranges if you think it is suitable for your printer. There are a lot of different type of printers, hot-ends and printer offsets that it is extremely difficult to give an overall one-size-fits-all setting.
*) If blobs/lumps form around the nozzle then your print temperature is too high.
Post processing MetalFil – Brass
Brushing and/or sand grinding
Once printed MetalFil – Brass objects can very easily be brushed with a brass brush or sanded with a fine grid sandpaper. By brushing and/or sand grinding your printed object you will brush/shine up the high concentration of brass powders.
Build-in white polish feature
After being brushed and/or sanded MetalFil – Brass will reveal its white polish feature. A very thin white layer/haze on your object will now allow you to easily polish your 3D print into a beautiful brass object.
Professional polishing with a rotary tumbler
Post processing a MetalFil – Brass 3D printed object with a rotary tumbler will make your FDM 3D printed object indistinguishable from genuine brass casted objects.
Waxing and coating
After every above mentioned post-processing measure you can always wax or coat your printed object to get an incredible shine effect. Waxing can be done with products such as beeswax and for coating one can think about products such as XTC-3D.
Please be aware that MetalFil filaments contain a very high concentration of metal powders, which have an abrasive nature. In general these metal powders will accelerate the nozzle-wear of brass nozzles, much faster than unfilled filaments. We recommend to use nozzles from stainless steel or other hardened alloys.
|ρ: 2.78 g/cc||50 gr coil||0.75 Kg spool|
|Ø 1.75mm||± 7.5m||± 112m|
|Ø 2.85mm||± 2.8m||± 42m|
When printing with filled/composite filaments it is recommended to clean your nozzle immediately after printing by feeding 15-20cm PLA filament through your nozzle. This will make sure that any potential fillers are flown out of your nozzle. It is even better to use glow in the dark PLA as the extremely hard phosphorous particles are much more likely to scrape out residual waste from your nozzle.
Product export information
|HS Code: 39169090||Description: Monofilament||Country of origin: the Netherlands|
This filament is compliant to below listed directives and regulations.
*) This declaration of conformity to directives and regulations is prepared according to our present standard of knowledge and may be amended if new cognitions are available and applies only for the above described products.
Solamente clienti che hanno effettuato l'accesso ed hanno acquistato questo prodotto possono lasciare una recensione.
Una spesa di almeno 50€.
*Tranquillo, non amiamo inviare mail di spam
Dai un LIKE alla nostra Pagina Facebook e ottieni subito un coupon del 10% per il tuo carrello.
Tutto quello che devi fare è regalarci un LIKE e confermare la tua mail.
Nota: Il coupon generato è valido solo se confermi la tua mail.